Please note: this is not the full representation of what we carry at the store. If you are looking to special order please call us at (423) 253-3133 or send an email at customerservice@yateshomepro.com.

Old Masters Wiping Stain

Old Masters

SKU: 514551



This is a cutting edge, robust, interior oil-based stain. Its thick, rich formula allows for easy application and superior color control, which is necessary to achieve a rich and uniform color on most surfaces in a single application.

Wiping Stain can be used on a variety of surfaces, including unfinished wood, previously finished surfaces, fiberglass, metal, and composition surfaces. Especially recommended for woods such as pine, birch, maple, poplar, and cherry.

Technical Data Sheet

Where to Use
Wiping Stain can be used on a variety of surfaces, including unfinished wood, previously finished surfaces, fiberglass, coated metal, and composition surfaces. Especially recommended for woods such as pine, birch, maple, poplar, and cherry.

Ideal for difficult-to-stain woods such as pine, poplar, maple, plywood, and veneers.

Surface Preparation
All surfaces must be clean, dry, and free from dirt, wax, grease, glue, and other contaminants or penetration and adhesion will be affected. Wood surfaces must be sanded smooth. Remove dust with a tack rag or a lint-free cloth dampened with mineral spirits. Surface defects should be repaired with an appropriate patching material.

Application
Stir thoroughly before and during application for even distribution of color. Stain application varies based on surface material. Always test stain in an inconspicuous area.

Application on Bare Wood (used as a stain): Color of stain will vary depending on wood type and porosity and method of application. After cleaning wood surface, sand with #120 or #180 sandpaper until smooth. Remove sanding dust. Apply stain liberally with brush, lint-free cloth, or spray until surface is completely wet. Allow to penetrate for 5 to 15 minutes. Wipe with a soft cloth, first across the grain, then with the grain. For a darker color, re-stain when first coat is dry. For a lighter color, wipe with a cloth dampened with paint thinner before the stain has dried.

Application on Fiberglass & Composition Surfaces: Stain one section or panel at a time. Apply a liberal coat of Wiping Stain with a firm synthetic brush or lint-free rag and work the stain across and into the grain uniformly, feathering out streaks while stain is wet. Wipe brush often on a lint-free rag to remove excess stain.

Application over Painted Surfaces (used as a glaze): Apply to thoroughly dry paint with cheesecloth or brush, using long, smooth strokes for simulated woodgraining, or blend gently from edges for other effects. Allow the stain to set up for approximately 5 to 10 minutes, then dry brush to subdue or blend. Allow stain to dry thoroughly (usually 12 hours or longer, depending on humidity and drying conditions). We do not recommend a lacquer-type finish over a glaze application.

Application over Previously Finished Surfaces: Lightly sand surface with very fine grit sandpaper or #0000 steel wool. Remove dust with a lint-free cloth or tack rag. With a foam or bristle brush, apply a thin uniform coat of Wiping Stain. Using a soft, dry bristle brush, make light, even strokes in the direction of the grain while allowing the grain pattern beneath the surface to show through. Continue to lightly brush the surface until the pattern is consistent and then allow the stain to dry. If you need to darken the color, apply an additional coat of stain in the same manner as the first coat. Allow stain to dry thoroughly (usually 12 hours or longer, depending on humidity and drying conditions).

Mixing and Tinting
You can achieve custom colors by intermixing Wiping Stain colors or by adding up to 10 ounces of universal or industrial colorant per gallon. Create Santa Fe pastel colors by tinting Pickling White Wiping Stain (formulas available upon request). Natural Tint Base Wiping Stain may be used to lighten a Wiping Stain color in any proportion or as a tint base for ultimate color selection. The amount of colorant added may affect its performance and extend the dry time. DO NOT THIN.

Coverage:
Approximately 500 square feet per gallon. Spreading rate will vary significantly depending on application method and condition of wood.

Drying Time
Approximately 10 hours, depending on humidity, temperature, and air movement. Dry times may also be extended due to excess stain application or lack of stain penetration. Wiping Stain can be topcoated after 12 hours, but stain must be thoroughly dry. When used on hardwood floors, allow 24 hours or longer depending on surface and drying conditions. Ideal drying conditions recommended are 70° to 75°F and 35 to 50% humidity.
**   Due to the nature and depth of color for the stain color Carbon Black, the minimum dry time is 24 hours.  Dry time may also be extended due to excess stain application or lack of stain penetration.

Cleanup
Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.

DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

 

Recommended Finish Coat
We recommend Old Masters clear finishes. However, this stain can be top coated with most clears. If a lacquer topcoat is desired, test for compatibility before using. For exterior use, we suggest Old Masters Spar-Marine Varnish or Old Masters Ascend Exterior. When applying water-based finishes, allow a minimum of 24 hours before top coating.

MAX VOC: 250 grams/liter (2 lbs/gal)

Pickling White
Old Masters Wiping Stain is also offered in a unique pickling white formula. Pickling white creates a classic, white washed appearance on wood. Contemporary, southwestern colors can be achieved using Old Masters Pickling White as a tint base. Santa Fe tint formulas are available upon request. Please use the following instructions for mixing and tinting. Please follow all other instructions listed above.

Mixing and Tinting
Create Santa Fe pastel colors by tinting Pickling White Wiping Stain with up to 2.5 ounces of colorant per quart. The amount of colorant added may affect its performance and extend the dry time. DO NOT THIN.

MAX VOC: 550 grams/liter (4.6 lbs/gal)


We Also Recommend